|
How to Anonymize or Delete Print History in Dashboard?
|
|
5
|
1166
|
November 25, 2023
|
|
Form Cure Firmware doesn't include new materials
|
|
0
|
249
|
November 24, 2023
|
|
Mixer keeps setting itself to an angle
|
|
1
|
279
|
November 16, 2023
|
|
Can the black dye used on Elastic 50A resin?
|
|
1
|
294
|
November 6, 2023
|
|
Chronic Form 3 print failures
|
|
2
|
584
|
November 1, 2023
|
|
Poor Quality on the Supports Side
|
|
21
|
6766
|
October 26, 2023
|
|
Advice needed - resin on the bottom of resin tank
|
|
3
|
492
|
October 27, 2023
|
|
Whats causing this? ONLY on one tank and resin
|
|
2
|
475
|
October 23, 2023
|
|
Castable wax 40 casting horrible
|
|
1
|
356
|
October 23, 2023
|
|
Very loud sound
|
|
1
|
289
|
October 16, 2023
|
|
Form auto not even attempting to remove part
|
|
3
|
362
|
October 16, 2023
|
|
Form auto not ejecting parts
|
|
2
|
236
|
October 16, 2023
|
|
Repeated failure to print. Initial platform ok...then nothing and a thick "board" found in the resin tank
|
|
6
|
386
|
October 12, 2023
|
|
Form 3 "Disconnected From Printer, Trying to Reconnect" Error in PreForm
|
|
2
|
453
|
October 11, 2023
|
|
Cartridge mismatch over ride
|
|
3
|
326
|
October 11, 2023
|
|
Form 3 misreading resin cartridge content amount
|
|
6
|
2449
|
October 11, 2023
|
|
Rigid 4000 Stiffness is Inconsistant
|
|
1
|
295
|
October 5, 2023
|
|
Failures with mini rafts/supports not printing on platform
|
|
6
|
562
|
October 4, 2023
|
|
Form3+ boot then shutdown after 2 seconds
|
|
1
|
291
|
October 2, 2023
|
|
The printer cannot tension the tank (3B)
|
|
1
|
617
|
September 29, 2023
|
|
Tank level inaccuracy causing long wait times before print
|
|
7
|
698
|
September 29, 2023
|
|
Resin Tank Cleaning
|
|
9
|
2417
|
September 28, 2023
|
|
Form3 not detecting resin level.... At all?!
|
|
9
|
844
|
September 25, 2023
|
|
3.31.1 update
|
|
5
|
687
|
September 21, 2023
|
|
When can the Form 3 support the open mode?
|
|
6
|
2425
|
September 20, 2023
|
|
Error code 1 again and again
|
|
2
|
463
|
September 18, 2023
|
|
Will floating geometry print successfully if i didn't get minima warning in Preform?
|
|
8
|
474
|
September 12, 2023
|
|
Bad prints out of brand New Form 3
|
|
469
|
51448
|
September 8, 2023
|
|
Cylindricity of the holes
|
|
6
|
441
|
September 8, 2023
|
|
After update, I have been getting more fails
|
|
7
|
537
|
August 31, 2023
|