Support & Troubleshooting

Fuse 1 This subsection can be used to tag your post as a conversation specifically aimed at the Fuse 1. Form 3L This subsection can be used to tag your post as a conversation specifically aimed at the Form 3L. Form 2 This subsection can be used to tag your post as a conversation specifically aimed at the Form 2. Materials Use this subsection to discuss and ask questions about materials for use on Formlabs machines. Form 1/1+ This subsection can be used to tag your post as a conversation specifically aimed at the Form 1 or Form 1+. Form 3/3+ This subsection can be used to tag your post as a conversation specifically aimed at the Form 3.

Topic	Replies	Views	Activity
Support & Troubleshooting Support & Troubleshooting	0	6525	July 8, 2014
Castable Wax 40 won't adhere to build platform Materials	0	3	June 3, 2023
Wash L Electric siphon pump not working Form 3L	1	21	June 2, 2023
Washing with solvents other then IPA/TPM for ultrasonic cleaner Support & Troubleshooting	6	71	June 2, 2023
Dispensing from 1 cartridge at a time Form 3L	4	143	June 1, 2023
Scraping/Grinding sound when LPU moves from right to left in between layers (Form 3/3B) Form 3/3+	8	86	May 30, 2023
The Fuse 1 cannot print Nylon 12 GF reliably Fuse 1	68	1858	May 30, 2023
Using printed parts for electrochemical cell Materials	1	47	May 30, 2023
Feedback on the Fuse series Fuse 1	0	66	May 29, 2023
Additional Resin Layers on Bottom side of print (opposite supported side) Form 3/3+	3	79	May 25, 2023
Print marks/silhouette on resin tank film. Should I be concerned? Form 3/3+	2	68	May 24, 2023
Mixer Check Failure, tried other fixes Form 3/3+	2	60	May 23, 2023
Error Code 1 Form 3/3+	3	818	May 20, 2023
Form3+ reliability - negative experience Support & Troubleshooting	5	108	May 19, 2023
Resin level sensor error Form 3L Support & Troubleshooting	7	113	May 19, 2023
Grey Resin: platform-side inaccurate Materials	1	48	May 18, 2023
Form 2 excess rashing and debris formation during printing Form 2	11	179	May 18, 2023
Removing Rigid 10K Parts Materials	4	73	May 15, 2023
Loosing the tips of points Form 2	2	84	May 15, 2023
Tear Down of a 3+ Form 3/3+	1	110	May 11, 2023
Wash evaporated - left a mess at the bottom Support & Troubleshooting	2	100	May 10, 2023
Optics test is great, but Form 2	7	1327	May 9, 2023
PreForm including models outside selection box when layer view activated Support & Troubleshooting	1	58	May 9, 2023
Random fails, how to improve success rate Form 3/3+	3	123	May 8, 2023
Form Cure Total LED Time Support & Troubleshooting	1	79	May 8, 2023
Enclosing the Form 3 in a grow tent Form 3/3+	2	114	May 8, 2023
Poor prints on Form2 Form 2	2	73	May 6, 2023
How accurate is the Powder estimate…? Fuse 1	8	156	May 5, 2023
Motor Jam. LPU completely STUCK Form 3/3+	22	2238	May 3, 2023
Dashboard show wrong amount of resin left Form 3/3+	26	944	May 1, 2023