|
About the Form 1/1+ category
|
|
1
|
3915
|
July 16, 2021
|
|
New Fuse1+
|
|
1
|
55
|
December 24, 2025
|
|
Form 1/1+ lid replacement parts
|
|
2
|
533
|
October 15, 2025
|
|
Enabling virtual printers in OpenFL PreForm 2.3.3 (Debug Mode)
|
|
1
|
55
|
October 11, 2025
|
|
Changing Form1 Name
|
|
20
|
231
|
June 13, 2025
|
|
Finishing position of roller is different after each print. Why?
|
|
0
|
20
|
May 31, 2025
|
|
Bad prints from form1 after switching resin
|
|
15
|
95
|
May 18, 2025
|
|
Fuse 1+ print problem
|
|
21
|
412
|
April 10, 2025
|
|
New 1+ owner - prints fail
|
|
14
|
1707
|
June 30, 2023
|
|
Issues Printing with Form 1+, OpenFL and Flexvat- Help Appreciated
|
|
2
|
1674
|
June 30, 2023
|
|
Aftermarket Form 1+ Laser Replacement
|
|
21
|
8569
|
June 20, 2023
|
|
Measurements errors
|
|
5
|
605
|
July 29, 2022
|
|
Z offset
|
|
3
|
737
|
June 17, 2022
|
|
1+ with firmware 1.40 - all prints failing, peel/tilt motor works fine
|
|
2
|
826
|
December 13, 2021
|
|
Form 1+ cover replacement
|
|
0
|
700
|
November 20, 2021
|
|
Waves / lines marks
|
|
8
|
814
|
November 11, 2021
|
|
Form 1+ power supply
|
|
7
|
4728
|
October 1, 2021
|
|
Silicone PDMS layer - possible to replace PDMS without replacing whole resin tray?
|
|
53
|
29011
|
September 2, 2021
|
|
1+ Peel Speed
|
|
0
|
870
|
July 28, 2021
|
|
Looking for a Form1+ glass print bed
|
|
1
|
1016
|
June 21, 2021
|
|
Form 1 Disconnects when starting print
|
|
5
|
2129
|
April 19, 2021
|
|
Building a resin tank question
|
|
6
|
1440
|
March 30, 2021
|
|
Form 1+ software in a form 1?
|
|
2
|
1065
|
March 23, 2021
|
|
F1+ Galvano mirror snapped off!
|
|
2
|
1412
|
February 11, 2021
|
|
How do I remove the mirror on Form1?
|
|
2
|
1210
|
January 26, 2021
|
|
Form1 doesn't boot
|
|
7
|
2946
|
January 4, 2021
|
|
Form 1: print offset problem
|
|
4
|
1124
|
December 30, 2020
|
|
Prints skewed/tilted, like a paralellogram, on formlabs form1
|
|
2
|
1366
|
November 11, 2020
|
|
Formlabs Form 1+
|
|
3
|
1521
|
October 11, 2020
|
|
Fried arm mcu
|
|
0
|
1099
|
September 17, 2020
|