|
Printer stopped printing
|
|
3
|
460
|
September 15, 2023
|
|
Form 3 LCD Screen glitch
|
|
17
|
4264
|
December 12, 2023
|
|
Première impression
|
|
0
|
143
|
December 11, 2023
|
|
Firmware latest update
|
|
5
|
447
|
December 5, 2023
|
|
Print this how? “best way”
|
|
4
|
251
|
December 5, 2023
|
|
Is it possible to change the glass of the Form 3 resin tank?
|
|
7
|
367
|
December 5, 2023
|
|
Estimated remaining resin in cartridge way off
|
|
3
|
309
|
December 5, 2023
|
|
Tiny rashes and lines at the very end layer
|
|
0
|
193
|
December 5, 2023
|
|
Force Form 3 to start print without filling
|
|
6
|
2224
|
December 1, 2023
|
|
New 3B+ firmware - Printer cant initialize
|
|
2
|
427
|
November 29, 2023
|
|
How to Anonymize or Delete Print History in Dashboard?
|
|
5
|
868
|
November 25, 2023
|
|
Form Cure Firmware doesn't include new materials
|
|
0
|
187
|
November 24, 2023
|
|
Mixer keeps setting itself to an angle
|
|
1
|
216
|
November 16, 2023
|
|
Can the black dye used on Elastic 50A resin?
|
|
1
|
187
|
November 6, 2023
|
|
Chronic Form 3 print failures
|
|
2
|
428
|
November 1, 2023
|
|
Poor Quality on the Supports Side
|
|
21
|
5735
|
October 26, 2023
|
|
Advice needed - resin on the bottom of resin tank
|
|
3
|
297
|
October 27, 2023
|
|
Whats causing this? ONLY on one tank and resin
|
|
2
|
410
|
October 23, 2023
|
|
Castable wax 40 casting horrible
|
|
1
|
286
|
October 23, 2023
|
|
Very loud sound
|
|
1
|
232
|
October 16, 2023
|
|
Form auto not even attempting to remove part
|
|
3
|
306
|
October 16, 2023
|
|
Form auto not ejecting parts
|
|
2
|
203
|
October 16, 2023
|
|
Repeated failure to print. Initial platform ok...then nothing and a thick "board" found in the resin tank
|
|
6
|
331
|
October 12, 2023
|
|
Form 3 "Disconnected From Printer, Trying to Reconnect" Error in PreForm
|
|
2
|
303
|
October 11, 2023
|
|
Cartridge mismatch over ride
|
|
3
|
239
|
October 11, 2023
|
|
Form 3 misreading resin cartridge content amount
|
|
6
|
2303
|
October 11, 2023
|
|
Rigid 4000 Stiffness is Inconsistant
|
|
1
|
243
|
October 5, 2023
|
|
Failures with mini rafts/supports not printing on platform
|
|
6
|
422
|
October 4, 2023
|
|
Form3+ boot then shutdown after 2 seconds
|
|
1
|
240
|
October 2, 2023
|
|
The printer cannot tension the tank (3B)
|
|
1
|
336
|
September 29, 2023
|