Is it possible to change the glass of the Form 3 resin tank?
|
|
7
|
307
|
December 5, 2023
|
Estimated remaining resin in cartridge way off
|
|
3
|
250
|
December 5, 2023
|
Tiny rashes and lines at the very end layer
|
|
0
|
168
|
December 5, 2023
|
Force Form 3 to start print without filling
|
|
6
|
2139
|
December 1, 2023
|
New 3B+ firmware - Printer cant initialize
|
|
2
|
372
|
November 29, 2023
|
How to Anonymize or Delete Print History in Dashboard?
|
|
5
|
813
|
November 25, 2023
|
Form Cure Firmware doesn't include new materials
|
|
0
|
148
|
November 24, 2023
|
Mixer keeps setting itself to an angle
|
|
1
|
171
|
November 16, 2023
|
Can the black dye used on Elastic 50A resin?
|
|
1
|
156
|
November 6, 2023
|
Chronic Form 3 print failures
|
|
2
|
378
|
November 1, 2023
|
Poor Quality on the Supports Side
|
|
21
|
5499
|
October 26, 2023
|
Advice needed - resin on the bottom of resin tank
|
|
3
|
258
|
October 27, 2023
|
Whats causing this? ONLY on one tank and resin
|
|
2
|
377
|
October 23, 2023
|
Castable wax 40 casting horrible
|
|
1
|
256
|
October 23, 2023
|
Very loud sound
|
|
1
|
211
|
October 16, 2023
|
Form auto not even attempting to remove part
|
|
3
|
289
|
October 16, 2023
|
Form auto not ejecting parts
|
|
2
|
191
|
October 16, 2023
|
Repeated failure to print. Initial platform ok...then nothing and a thick "board" found in the resin tank
|
|
6
|
316
|
October 12, 2023
|
Form 3 "Disconnected From Printer, Trying to Reconnect" Error in PreForm
|
|
2
|
275
|
October 11, 2023
|
Cartridge mismatch over ride
|
|
3
|
222
|
October 11, 2023
|
Form 3 misreading resin cartridge content amount
|
|
6
|
2250
|
October 11, 2023
|
Rigid 4000 Stiffness is Inconsistant
|
|
1
|
216
|
October 5, 2023
|
Failures with mini rafts/supports not printing on platform
|
|
6
|
372
|
October 4, 2023
|
Form3+ boot then shutdown after 2 seconds
|
|
1
|
219
|
October 2, 2023
|
The printer cannot tension the tank (3B)
|
|
1
|
277
|
September 29, 2023
|
Tank level inaccuracy causing long wait times before print
|
|
7
|
500
|
September 29, 2023
|
Resin Tank Cleaning
|
|
9
|
2206
|
September 28, 2023
|
Form3 not detecting resin level.... At all?!
|
|
9
|
655
|
September 25, 2023
|
3.31.1 update
|
|
5
|
405
|
September 21, 2023
|
When can the Form 3 support the open mode?
|
|
6
|
2101
|
September 20, 2023
|