# Yellow Magic vs IPA **URL:** \ **Category:** General Discussion\ **Created:** [August 16, 2016, 2:41am UTC](https://forum.formlabs.com/t/yellow-magic-vs-ipa/9284 "2016-08-16T02:41:20Z")\ **Posts on this page:** 4\ **Page:** 1
**Author:** ![DerekMurphy](https://avatars.discourse-cdn.com/v4/letter/d/a183cd/32.png) [@DerekMurphy](https://forum.formlabs.com/u/DerekMurphy)\ **Post date:** [August 16, 2016, 2:41am UTC](https://forum.formlabs.com/t/yellow-magic-vs-ipa/9284/1 "2016-08-16T02:41:20Z")
I know switching to Yellow Magic has been talked about online in the past. I know that YM coagulates versus the IPA that dissolves the resin. When I use the YM as the first rinse the part gets all sticky. I’ve used a very soft brush and a heavier brush to clean with the YM. I’ve test with 2 washes of YM, 1 YM and 1 IPA, 2 IPA (standard). I would like to see if anyone else has this issue when using YM or if I am just missing something. ---
**Author:** ![Marty\_Castilla](https://avatars.discourse-cdn.com/v4/letter/m/c2a13f/32.png) [@Marty\_Castilla](https://forum.formlabs.com/u/Marty_Castilla)\ **Post date:** [August 25, 2016, 8:15pm UTC](https://forum.formlabs.com/t/yellow-magic-vs-ipa/9284/2 "2016-08-25T20:15:26Z")
I have the same question, my parts are collecting some of the finer coagulated material. I’m using an ultrasonic cleaner with the YM. I logged in today to see if someone has posted their working YM process. Still searching the forums. ---
**Author:** ![Marty\_Castilla](https://avatars.discourse-cdn.com/v4/letter/m/c2a13f/32.png) [@Marty\_Castilla](https://forum.formlabs.com/u/Marty_Castilla)\ **Post date:** [August 25, 2016, 8:24pm UTC](https://forum.formlabs.com/t/yellow-magic-vs-ipa/9284/3 "2016-08-25T20:24:55Z")
Ok here is what I found: > [@Yellow Magic 7 Qustions](http://forum.formlabs.com/t/yellow-magic-7-qustions/8185/9): > > You’ll have to take my comments with a grain of salt since I’m not an expert, but I had to clean a very large print last night and didn’t have enough IPA, so I went with a 1:1 mixture of YM7 and water and put the part into it. I put the finishing tank on my investment vibrator and shook it for about 5 minutes. I pulled out the part and rinsed it off and let it dry. Afterward it was very tacky. I then put the part into the other tank with clean IPA and swooshed and flipped it there for a coup… and > [@Yellow Magic 7 Qustions](http://forum.formlabs.com/t/yellow-magic-7-qustions/8185/13): > > When we first starting printing with our Form 2, we were trying to only use YM7, but our parts were always still tacky. After experimenting, we ended up using YM7 as the first rinse (shaking for a minute then letting set for another 15 minutes), then using IPA as the second/final rinse. Our parts have been turning out great since that change. We’re a little disappointed in the YM7, but it is still helping to minimize the amount of IPA we end up using. ---
**Author:** ![Sethcim](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/sethcim/32/16361_2.png) [@Sethcim](https://forum.formlabs.com/u/Sethcim)\ **Post date:** [June 1, 2020, 5:12pm UTC](https://forum.formlabs.com/t/yellow-magic-vs-ipa/9284/4 "2020-06-01T17:12:28Z")
So far I can’t get parts all the way clean with yellow magic without mechanical agitation (i.e. brushing).