# Slow tank fill

**URL:** <https://forum.formlabs.com/t/slow-tank-fill/37199>\
**Category:** Form 3L\
**Created:** [November 6, 2023, 8:42pm UTC](https://forum.formlabs.com/t/slow-tank-fill/37199 "2023-11-06T20:42:08Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![SteamFactory](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/steamfactory/32/19952_2.png) [@SteamFactory](https://forum.formlabs.com/u/SteamFactory)\
**Post date:** [November 6, 2023, 8:42pm UTC](https://forum.formlabs.com/t/slow-tank-fill/37199/1 "2023-11-06T20:42:08Z")

</div>

Realizing that an empty 3L tank takes a while to fill, I’m currently seeing an extremely slow fill on this particular 3L.

These are the events that occurred:

- Print sent to printer Friday afternoon (this is a 34hr print)
- Saturday morning noticed print was paused in dashboard.
- Went to the lab to inspect, no resin had been dispensed into the tank.
- Re-seated the catrdiges and observed a very, very slow trickle of resin into the tank.
- Monday morning, printer again errored out due to no resin
- Pulled cartridges, removed the nipples and made sure there were no clogs in the cartridge
- Replaced cartridges and resumed
- Resin begain flowing as expected for about 5 minutes then stopped. I assumed that might be normal
- Came back several hours later. No resin flowing and the tank was not filled.

This seems to be going way too slow. I shook the cartridges slightly while installed and resin flowed out but then stopped. Should it really take 8 hours to fill a tank? This is not what I experienced with my other 3L

---

<div class="post-metadata">

**Author:** ![Jesse\_K](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/jesse_k/32/18872_2.png) [@Jesse\_K](https://forum.formlabs.com/u/Jesse_K)\
**Post date:** [November 6, 2023, 9:34pm UTC](https://forum.formlabs.com/t/slow-tank-fill/37199/2 "2023-11-06T21:34:15Z")

</div>

Hi @SteamFactory,

Thanks for reaching out. The resin dispense should be flowing in a small, steady stream (much like a thin pencil lead). We recommend manually pouring a full liter of resin into an empty 3L resin tank prior to starting the print to cut down on filling time. If no resin is dispensing at all over a long time period, there might be an issue with the printer’s resin level sensing system. I would advise [getting in touch with Support](https://support.formlabs.com/s/contact-support?language=en_US) for them to check the printer’s diagnostic logs for further insight.

---

<div class="post-metadata">

**Author:** ![SteamFactory](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/steamfactory/32/19952_2.png) [@SteamFactory](https://forum.formlabs.com/u/SteamFactory)\
**Post date:** [November 7, 2023, 3:18pm UTC](https://forum.formlabs.com/t/slow-tank-fill/37199/3 "2023-11-07T15:18:14Z")

</div>

Thanks Jess,  
Our service tech and I have determined that the finger lever thing that pinches the rubber dispensing nozzle at the bottom of the cartridge has become gummed up with resin. Cleaning this fixed the problem.

I intentionally did not pre-fill the tank as I wanted to see how long it would take to fill from empty.
