# Lots of holes on the print

**URL:** <https://forum.formlabs.com/t/lots-of-holes-on-the-print/8782>\
**Category:** Form 1/1+\
**Created:** [June 29, 2016, 5:02pm UTC](https://forum.formlabs.com/t/lots-of-holes-on-the-print/8782 "2016-06-29T17:02:15Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![danli](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/danli/32/6662_2.png) [@danli](https://forum.formlabs.com/u/danli)\
**Post date:** [June 29, 2016, 5:02pm UTC](https://forum.formlabs.com/t/lots-of-holes-on-the-print/8782/1 "2016-06-29T17:02:15Z")

</div>

![](https://us1.discourse-cdn.com/flex025/uploads/formlabs/original/2X/8/8d6a5fc2807eadcd9608e5904c43ff73e269aea1.JPG)  
 ![](https://us1.discourse-cdn.com/flex025/uploads/formlabs/original/2X/1/10d9ae16e8f1040b1be9db8ad893699a905d21ca.JPG)  
 ![](https://us1.discourse-cdn.com/flex025/uploads/formlabs/original/2X/7/79f12ebff3b66cb0acd383037350a1b1430ecaff.JPG)

As you can see from the pictures. The right one was the first try. The bottom part looks fine but the side connected with the support has a lot of holes, and the print breaked in the middle. The seconded try also has lots of holes on it.  
The model works fine on other kinds of 3d printer. The material is makerjuice SF.

Thanks.

---

<div class="post-metadata">

**Author:** ![DavidRosenfeld](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/davidrosenfeld/32/3570_2.png) [@DavidRosenfeld](https://forum.formlabs.com/u/DavidRosenfeld)\
**Post date:** [June 29, 2016, 8:56pm UTC](https://forum.formlabs.com/t/lots-of-holes-on-the-print/8782/2 "2016-06-29T20:56:00Z")

</div>

Have you tried printing the same model in the same orientation with Formlabs resin? Have you had success with Makerjuice SF resin in the past?

---

<div class="post-metadata">

**Author:** ![Randy\_Cohen](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/randy_cohen/32/1500_2.png) [@Randy\_Cohen](https://forum.formlabs.com/u/Randy_Cohen)\
**Post date:** [June 30, 2016, 3:41am UTC](https://forum.formlabs.com/t/lots-of-holes-on-the-print/8782/3 "2016-06-30T03:41:38Z")

</div>

You’re not using the correct settings for the resin, or the resin is NG. This does not appear to have the “hallmarks” of dirty optics, which can result in prints similar in look. But this isn’t that, near as I can say…

---

<div class="post-metadata">

**Author:** ![system](https://us1.discourse-cdn.com/flex025/uploads/formlabs/original/3X/5/b/5bc2bdf993ff27c2e0eecab5010b25626fbb327a.png) [@system](https://forum.formlabs.com/u/system)\
**Post date:** [July 15, 2016, 9:56am UTC](https://forum.formlabs.com/t/lots-of-holes-on-the-print/8782/4 "2016-07-15T09:56:40Z")

</div>

This topic was automatically closed 15 days after the last reply. New replies are no longer allowed.