# Form4 Elastic 50A discoloured in tank

**URL:** <https://forum.formlabs.com/t/form4-elastic-50a-discoloured-in-tank/46115>\
**Category:** Form 4/B/L\
**Created:** [February 27, 2026, 2:33pm UTC](https://forum.formlabs.com/t/form4-elastic-50a-discoloured-in-tank/46115 "2026-02-27T14:33:56Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![MurphKieran](https://avatars.discourse-cdn.com/v4/letter/m/f475e1/32.png) [@MurphKieran](https://forum.formlabs.com/u/MurphKieran)\
**Post date:** [February 27, 2026, 2:33pm UTC](https://forum.formlabs.com/t/form4-elastic-50a-discoloured-in-tank/46115/1 "2026-02-27T14:33:57Z")

</div>

I loaded a bottle of Elastic 50A into my Form 4 less than seven days ago into a brand new tank with mixer. I printed several models with great success and got my desired white/clear post-processing results. I sent another print this morning but noticed, while removing the model, that the resin was discoloured and yellow. Twenty-four hours previously, the print pictured came out transparent. Any ideas as to what caused the resin to discolour so quickly?

 ![Image (13)](https://us1.discourse-cdn.com/flex025/uploads/formlabs/original/3X/9/9/991d96c9b257b3e0314172f6d598a13ceb727357.jpeg)

 ![Image (14)](https://us1.discourse-cdn.com/flex025/uploads/formlabs/original/3X/3/f/3f3b5906edaa390181b345f03c92dd8528412ad1.jpeg)

 ![Image (15)](https://us1.discourse-cdn.com/flex025/uploads/formlabs/original/3X/4/f/4f986b77180316de0a0b7f201e1db8b67b769039.jpeg)

---

<div class="post-metadata">

**Author:** ![serret](https://avatars.discourse-cdn.com/v4/letter/s/3d9bf3/32.png) [@serret](https://forum.formlabs.com/u/serret)\
**Post date:** [February 27, 2026, 3:25pm UTC](https://forum.formlabs.com/t/form4-elastic-50a-discoloured-in-tank/46115/2 "2026-02-27T15:25:47Z")

</div>

I’m on Form 3L so my experience may differ but :  
My resin tank and prints always have a yellow tint before curing them underwater.

After an underwater cure the tackiness and tint are gone and my result look like your finished part on the third picture.

---

<div class="post-metadata">

**Author:** ![brendancapuano](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/brendancapuano/32/22524_2.png) [@brendancapuano](https://forum.formlabs.com/u/brendancapuano)\
**Post date:** [February 27, 2026, 8:33pm UTC](https://forum.formlabs.com/t/form4-elastic-50a-discoloured-in-tank/46115/3 "2026-02-27T20:33:53Z")

</div>

Good question @MurphKieran - We recommend to wash the parts as normal and then cure them. Wait 24-72 hours after you cure the part, and some if not all of that yellowing, should dissipate back to clear.

---

<div class="post-metadata">

**Author:** ![jantarek](https://avatars.discourse-cdn.com/v4/letter/j/dfb087/32.png) [@jantarek](https://forum.formlabs.com/u/jantarek)\
**Post date:** [September 16, 2026, 5:46pm UTC](https://forum.formlabs.com/t/form4-elastic-50a-discoloured-in-tank/46115/4 "2026-09-16T17:46:55Z")

</div>

did the print turrned back to clear? I did quite a bit of elastic 50a in form 3 and now that I have form4 I just got back to elastic “flexible 50a v2” and the same all prints are yellow 😃

 ![IMG_4083](https://us1.discourse-cdn.com/flex025/uploads/formlabs/original/3X/c/1/c13702bb69abf3163827ff4146a28378941d29c1.jpeg)

---

<div class="post-metadata">

**Author:** ![leonhart88](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/leonhart88/32/19153_2.png) [@leonhart88](https://forum.formlabs.com/u/leonhart88)\
**Post date:** [September 17, 2026, 6:49am UTC](https://forum.formlabs.com/t/form4-elastic-50a-discoloured-in-tank/46115/5 "2026-09-17T06:49:20Z")

</div>

They tend to be yellow in the green state and then turn clear after curing.

---

<div class="post-metadata">

**Author:** ![Murtadha7](https://avatars.discourse-cdn.com/v4/letter/m/a9a28c/32.png) [@Murtadha7](https://forum.formlabs.com/u/Murtadha7)\
**Post date:** [September 28, 2026, 2:59pm UTC](https://forum.formlabs.com/t/form4-elastic-50a-discoloured-in-tank/46115/6 "2026-09-28T14:59:50Z")

</div>

I do have a similar issue with this, however I do use ESD resin as well so this might causes issues when washing it with the form wash bucket; I did find that leaving the cured “tacky” part underwater with no curing overnight, it becomes somewhat clear; not sure why that happens
