# Comb designed for cleaning the resin tank

**URL:** <https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031>\
**Category:** Projects & Prints\
**Created:** [March 24, 2015, 8:26am UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031 "2015-03-24T08:26:57Z")\
**Posts on this page:** 20\
**Page:** 3

<div class="post-metadata">

**Author:** ![Jolmer](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/jolmer/32/3430_2.png) [@Jolmer](https://forum.formlabs.com/u/Jolmer)\
**Post date:** [May 4, 2015, 9:08pm UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/41 "2015-05-04T21:08:11Z")

</div>

… or you could print my form file? It’s ‘ready to go’? 😉

You can also find my design on Thingiverse:

> **[Form 1 Resin Tank Comb by Evenredig](https://www.thingiverse.com/thing:799089)**
>
> To filter the content of the resin tank for small particles, that sometimes float around in the resin after printing, I made a resin tank comb. It fits exactly in the resin tank of the Form 1 (also the Form 1+).  
> This resin tank comb is based on the...

---

<div class="post-metadata">

**Author:** ![Josh\_Armstrong](https://avatars.discourse-cdn.com/v4/letter/j/b5e925/32.png) [@Josh\_Armstrong](https://forum.formlabs.com/u/Josh_Armstrong)\
**Post date:** [June 5, 2015, 4:12pm UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/42 "2015-06-05T16:12:14Z")

</div>

Hey Jolmer,

I’m using your form thingiverse file. Just to be clear you printed it successfully with just these supports. I ask because I noticed when I went into the edit support mode there was a lot of red on the model.  
 ![](http://forum.formlabs.com/uploads/formlabs/3765/5c47f0bc3aca32cb.png)  
 ![](http://forum.formlabs.com/uploads/formlabs/3764/e6253c0a20dd7819.png)

---

<div class="post-metadata">

**Author:** ![KevinHolmes](https://avatars.discourse-cdn.com/v4/letter/k/3ec8ea/32.png) [@KevinHolmes](https://forum.formlabs.com/u/KevinHolmes)\
**Post date:** [June 5, 2015, 9:51pm UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/43 "2015-06-05T21:51:11Z")

</div>

I went through several build-your-own-strainer iterations, but in the end I found as many others did, it’s already been done and is very affordable :

![](http://forum.formlabs.com/uploads/formlabs/3767/7858cf3f8e38b6ee.jpg)

A few coins for 50 at a time and each one will do two or more tanks.

Pouring the resin through a strainer is a total solution, whereas pushing a comb through the tank will never be 100% - never mind the fact that the nylon paint strainer mesh will always be finer than the F1 can print …

---

<div class="post-metadata">

**Author:** ![Jolmer](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/jolmer/32/3430_2.png) [@Jolmer](https://forum.formlabs.com/u/Jolmer)\
**Post date:** [June 8, 2015, 1:35pm UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/44 "2015-06-08T13:35:10Z")

</div>

Yes, I printed it with just these supports. All went well… 😉

---

<div class="post-metadata">

**Author:** ![Jolmer](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/jolmer/32/3430_2.png) [@Jolmer](https://forum.formlabs.com/u/Jolmer)\
**Post date:** [June 8, 2015, 1:36pm UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/45 "2015-06-08T13:36:06Z")

</div>

Where did you buy these, Kevin?

---

<div class="post-metadata">

**Author:** ![KevinHolmes](https://avatars.discourse-cdn.com/v4/letter/k/3ec8ea/32.png) [@KevinHolmes](https://forum.formlabs.com/u/KevinHolmes)\
**Post date:** [June 8, 2015, 2:02pm UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/46 "2015-06-08T14:02:40Z")

</div>

@Jolmer I’m in the UK so I got them from Amazon UK - £6.19 for 50, although I can see equivalent ones (same mesh size) on ebay cheaper now. Just google “paper paint strainer” to find some local to you - ebay/amazon/whatever…

---

<div class="post-metadata">

**Author:** ![Michael\_Breitenstein](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/michael_breitenstein/32/3125_2.png) [@Michael\_Breitenstein](https://forum.formlabs.com/u/Michael_Breitenstein)\
**Post date:** [June 9, 2015, 6:48am UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/47 "2015-06-09T06:48:49Z")

</div>

Hi Kevin  
That’s a good idea. But I have a question concerning the usage of the strainer. Do you filter your resin after every print job and do you clean the tank as well every time?

---

<div class="post-metadata">

**Author:** ![KevinHolmes](https://avatars.discourse-cdn.com/v4/letter/k/3ec8ea/32.png) [@KevinHolmes](https://forum.formlabs.com/u/KevinHolmes)\
**Post date:** [June 9, 2015, 8:19am UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/48 "2015-06-09T08:19:22Z")

</div>

@Michael_Breitenstein not my idea, think several others arrived at it independantly, not sure who mentioned it first.

Anyway - yes, filter after every print. The new F1+ laser generates a lot more flakes than a healthy F1. Filtering after every print is pretty much necessary unless you were lucky with your F1+ out of the box laser flare variance.

There’s no need to clean vats, even if you change resin types, mixing a few mls of different resin is of no consequence - unless you’re concerned about colour - eg a few mls of black could tint a whole vat.

In fact cleaning a vat is more likely to cause issues than prevent them - you’re increasing the risk of dust/fingerprints/smudges on the vat underside surface.

---

<div class="post-metadata">

**Author:** ![Anthony\_Huczek](https://avatars.discourse-cdn.com/v4/letter/a/ce7236/32.png) [@Anthony\_Huczek](https://forum.formlabs.com/u/Anthony_Huczek)\
**Post date:** [June 9, 2015, 6:23pm UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/49 "2015-06-09T18:23:55Z")

</div>

Filters are better than a comb but I haven’t used them on resin after each print very often. I have had pretty great success with the precautions I currently take so unless I run into an issue I won’t go through the trouble of filtering after every print.

I have tried using strainers to clean out my IPA solution a couple of times though. I have had multiple instances where the mesh separates from the paper due to the weight of the partially cured resin globs though. It gets to a point where the partially cured resin just blocks the passages anyway. I have a feeling just putting the tub out in the sun would be a better bet…

---

<div class="post-metadata">

**Author:** ![WillWalker](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/willwalker/32/76_2.png) [@WillWalker](https://forum.formlabs.com/u/WillWalker)\
**Post date:** [June 10, 2015, 2:02pm UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/50 "2015-06-10T14:02:51Z")

</div>

This is a great thread - the invention is really cool.

Last year I tried designing a comb but wasn’t satisfied at the time it took to filter or the performance. Personally, I haven’t found filtering necessary between most prints, unless the resin is getting older.

---

<div class="post-metadata">

**Author:** ![Schoner](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/schoner/32/8152_2.png) [@Schoner](https://forum.formlabs.com/u/Schoner)\
**Post date:** [July 4, 2016, 12:17pm UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/51 "2016-07-04T12:17:47Z")

</div>

I just found this discussion while I planned to start a new thread,  
So I will hook in…

When reading the guidelines for keeping a clean resin tank I also found the advice to use a comb for filtering the resin.  
I tried this first too, but found it was not very comfortable.  
So I created this “floaty filter” for the Form 2 to remove those particles of cured resin.  
It has a rack, which can be installed at the right side of the tank.  
So the filter is well stored and allways close to hand. It can drip off after each use below the uv-protected cover.  
The filter and its rack neither obstruct the wiper, build platform nor cover.  
And the best part: It’s printed by the dedicated machine itself. 🙂

 ![](https://us1.discourse-cdn.com/flex025/uploads/formlabs/original/2X/5/519c51aa38adb1580b16d54c323d6d12759142a6.jpg)

Best regards  
Jürgen Schoner

---

<div class="post-metadata">

**Author:** ![flipmoo](https://avatars.discourse-cdn.com/v4/letter/f/90ced4/32.png) [@flipmoo](https://forum.formlabs.com/u/flipmoo)\
**Post date:** [July 28, 2016, 3:13pm UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/52 "2016-07-28T15:13:58Z")

</div>

Hi Jurgen,

Is your solution also available for download??

---

<div class="post-metadata">

**Author:** ![aad345](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/aad345/32/5444_2.png) [@aad345](https://forum.formlabs.com/u/aad345)\
**Post date:** [July 29, 2016, 11:28am UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/53 "2016-07-29T11:28:30Z")

</div>

Looks amazing!

Would you be willing to share this model?

---

<div class="post-metadata">

**Author:** ![Schoner](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/schoner/32/8152_2.png) [@Schoner](https://forum.formlabs.com/u/Schoner)\
**Post date:** [July 31, 2016, 3:55pm UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/54 "2016-07-31T15:55:07Z")

</div>

Yes of course.  
There it is:  
[http://www.see3.de/demo/Floaty-Filter.zip](http://www.see3.de/demo/Floaty-Filter.zip)  
Give me a feedback, how it works.

---

<div class="post-metadata">

**Author:** ![aad345](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/aad345/32/5444_2.png) [@aad345](https://forum.formlabs.com/u/aad345)\
**Post date:** [August 3, 2016, 9:19am UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/55 "2016-08-03T09:19:10Z")

</div>

I think your design should be featured by Formlabs 😉

---

<div class="post-metadata">

**Author:** ![Macro](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/macro/32/6285_2.png) [@Macro](https://forum.formlabs.com/u/Macro)\
**Post date:** [August 3, 2016, 10:36am UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/56 "2016-08-03T10:36:47Z")

</div>

Thank you for putting that up!

I just had a fail with my flexible resin (my fault), and that will come in very useful. 😀

---

<div class="post-metadata">

**Author:** ![Schoner](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/schoner/32/8152_2.png) [@Schoner](https://forum.formlabs.com/u/Schoner)\
**Post date:** [August 4, 2016, 12:50pm UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/57 "2016-08-04T12:50:22Z")

</div>

Why in flexible? It wasn’t intended as a fishing net. 😉

---

<div class="post-metadata">

**Author:** ![Macro](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/macro/32/6285_2.png) [@Macro](https://forum.formlabs.com/u/Macro)\
**Post date:** [August 4, 2016, 10:37pm UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/58 "2016-08-04T22:37:08Z")

</div>

No, the mishap was in my flexible tank, so I am printing your gadget in tough resin. 😜

---

<div class="post-metadata">

**Author:** ![Hillzzz](https://avatars.discourse-cdn.com/v4/letter/h/5daacb/32.png) [@Hillzzz](https://forum.formlabs.com/u/Hillzzz)\
**Post date:** [August 5, 2016, 9:31am UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/59 "2016-08-05T09:31:19Z")

</div>

I gave the code for the first UK eCommerce site and payment gateway away for free.20 years ago. Now anyone can set up an online shop with open source software and I am happy that folks don’t have to pay huge licence fees to set up a small shop.  
The world needs more kind acts - I salute your open-hearted generosity. Your friend needs to learn money is not everything.  
Schoner - your comb is a great design and thank you for your generosity too.

---

<div class="post-metadata">

**Author:** ![Schoner](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.formlabs.com/schoner/32/8152_2.png) [@Schoner](https://forum.formlabs.com/u/Schoner)\
**Post date:** [August 7, 2016, 7:49pm UTC](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031/60 "2016-08-07T19:49:13Z")

</div>

Thanks a lot for your kind words.  
And I quite agree to your approach.

BTW:  
It seems, that the filter is rather popular. I could record 110 downloads so far. 🙂  
Would be happy to hear your experience with it.

[Previous page](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031.md?page=2)

[Next page](https://forum.formlabs.com/t/comb-designed-for-cleaning-the-resin-tank/4031.md?page=4)
