# Adjustable feets for Height under the Form1+ printer
**URL:** https://forum.formlabs.com/t/adjustable-feets-for-height-under-the-form1-printer/3230
**Category:** Feature Requests & Ideas
**Created:** [January 9, 2015, 9:49am UTC](https://forum.formlabs.com/t/adjustable-feets-for-height-under-the-form1-printer/3230 "2015-01-09T09:49:08Z")
**Posts on this page:** 7
**Page:** 1
### Author:  [@MarcusKnorr](https://forum.formlabs.com/u/MarcusKnorr)
#### Post date: [January 9, 2015, 9:49am UTC](https://forum.formlabs.com/t/adjustable-feets-for-height-under-the-form1-printer/3230/1 "2015-01-09T09:49:08Z")
It happend to me that my office table wasn’t 100% even. If my resin tank was completly filled the resin was very close to sip over the border when the build platform was moved in! I put something under my printer to make it even but it would be nice if it would be adjustable itself.
---
### Author:  [@Alex\_Vermeer](https://forum.formlabs.com/u/Alex_Vermeer)
#### Post date: [January 9, 2015, 10:43am UTC](https://forum.formlabs.com/t/adjustable-feets-for-height-under-the-form1-printer/3230/2 "2015-01-09T10:43:59Z")
You have a 3d printer! you can print them yourself 🙂
Could be something for the Form1++ or 2 though! good idea
---
### Author:  [@MarcusKnorr](https://forum.formlabs.com/u/MarcusKnorr)
#### Post date: [January 9, 2015, 11:49am UTC](https://forum.formlabs.com/t/adjustable-feets-for-height-under-the-form1-printer/3230/3 "2015-01-09T11:49:31Z")
thank you Alex 😉
I think I will just order some leveling screws but I possibly design the rubber feets for them.
[http://www.stoeffl.at/katalog/ki/Stellfuesse-Nivellierschrauben-72.html](http://www.stoeffl.at/katalog/ki/Stellfuesse-Nivellierschrauben-72.html)
[http://www.jwwinco.com/products/section7/](http://www.jwwinco.com/products/section7/)
---
### Author:  [@EvanFoss](https://forum.formlabs.com/u/EvanFoss)
#### Post date: [January 9, 2015, 2:01pm UTC](https://forum.formlabs.com/t/adjustable-feets-for-height-under-the-form1-printer/3230/4 "2015-01-09T14:01:59Z")
A bubble level integrated into the machine would be good too.
---
### Author:  [@JasonLivingston](https://forum.formlabs.com/u/JasonLivingston)
#### Post date: [January 9, 2015, 3:18pm UTC](https://forum.formlabs.com/t/adjustable-feets-for-height-under-the-form1-printer/3230/5 "2015-01-09T15:18:41Z")
@MarcusKnorr the current feet use a 6-32 screw (one of the only non-metric screws in the machine), so if you’re looking for some drop-in replacements, that should help. Something else to look for on the spec sheet is “non-marking.” I’ve found some feet that look great, but mark up your desk as if they’re oil pastels – really annoying if you’re trying to keep a clean workspace!
---
### Author:  [@MarcusKnorr](https://forum.formlabs.com/u/MarcusKnorr)
#### Post date: [January 9, 2015, 7:14pm UTC](https://forum.formlabs.com/t/adjustable-feets-for-height-under-the-form1-printer/3230/6 "2015-01-09T19:14:49Z")
@JasonLivingston thank you Jason great info! 😉
---
### Author:  [@ChristopherBarr](https://forum.formlabs.com/u/ChristopherBarr)
#### Post date: [January 9, 2015, 8:27pm UTC](https://forum.formlabs.com/t/adjustable-feets-for-height-under-the-form1-printer/3230/7 "2015-01-09T20:27:15Z")
On my lightbox, (outlined here: [A DIY UV post-cure Lightbox you too can make](http://forum.formlabs.com/t/a-diy-uv-post-cure-lightbox-you-too-can-make/2732) ) I used these adjustable felt feet: [http://www.homedepot.com/p/Everbilt-1-in-Threaded-Stem-Furniture-Glides-with-Felt-Base-4-per-Pack-49908/203661113](http://www.homedepot.com/p/Everbilt-1-in-Threaded-Stem-Furniture-Glides-with-Felt-Base-4-per-Pack-49908/203661113)
What’s nice about them, is they don’t grip the surface, and allow easy spinning adjustment. They are not 6-32 though, so cannot go into the Form1+ directly. You could simply put them into a piece of plywood or MDF and set the form1+ on it though…
-C